engine coolant FIAT 127 1977 1.G Workshop Manual

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
4/34
2. Specifications

Capacities (1049 cc models )
Engine oil (including filter change)
L, C and CL ... ... ... ... ... ... ... ... … 5.5 pints (3.1 litres)
Sport ... ... ... ... ... ... ... ... ... 7.7 pi nts (4.4 litres)

Coolant ... ... ... ... ... ... ... ... … 9.7 pints (5.5 litres)

Fuel ... ... ... ... ... ... ... ... … 6.7 gallons (30 .5 litres) including 6.2 pints
(3.5 litres) reserve

Transmission oil ... … ... ... ... ... ... ... . 4.2 pints (2.4 l itres)


1049 cc OHC engine
General
Type number ... ... ... ... ... ... ... ... … 127 A 000 (C, L and CL);
127 A1.000 (Sport)
Bore ... ... ... ... ... ... ... ... … 2.992 in (76 mm)
Stroke ... ... ... ... ... ... ... ... ... 2.276 in (57.8 mm)
Capacity ... ... ... ... ... ... ... ... … 64 cu in (1049 cc)
Compression ratio ... ... ... ... ... … 9,3 : 1 (C, L and CL);
9,8 : 1 (Sport)
Maximum horsepower (DIN) ... ... ... ... 50 HP a t 5600 rpm (C, L and CL);
70 HP at 5600 rpm (Sport)

Valve mechanism C, L and CL Sport
Inlet :
Opens ... ... ... ... ... ... ... ... ... 2° B TDC 6° BTDC
Closes ... ... ... ... ... ... ... ... ... 42° ABDC 46°ABDC
Exhaust :
Opens ... ... ... ... ... ... ... ... ... 42° BBDC 47° BBDC
Closes ... ... ... ... ... ... ... … … 2° ATDC 7° ATDC
Valve clearances (cold) :
For checking valve timing:
Inlet ... ... ... ... ... ... ... ... 0.02 8 in (0.70 mm) 0.032 in (0.80 mm)
Exhaust ... ... ... ... ... ... ... 0.028 in (0.70 mm) 0.032 in (0.80 mm)
Adjustment for running (engine cold) :
Inlet ... ... ... ... ... ... ... ... 0.01 2 in (0.30 mm) 0.016 in (0.40 mm)
Exhaust ... ... ... ... ... ... ... 0.016 i n (0 40 mm) 0.020 in (0.50 mm)

Cylinder block and connecting rods inches mm
Cylinder bore diameter * 2.992 to 2.994 76.00 to 7 6.05
* Cylinder bores are graded and have a variation of 0.0004 inch (0.01 mm) between each grade
Main bearing housing bore diameter 2.044 to 2.045 51.921 to 51.934
Width of centre main bearing cap between

thrust washers 1.088 to 1.091 27.64 to 27.70
Connecting rod big-end diameter 1.85 to 1.8560 47. 130 to 47.142
Connecting rod small-end diameter 0.8638 to 0.8646 21.94 to 21.96
Big-end bearing shell thickness 0.0606 to 0.8646 1. 539 to 1.55

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
7/34
Camshaft bearing bore diameter in head:
Valve gear end 1.1807 to 1.1817 29.990 to 30.015
Centre 1.0648 to 1.0657 27.045 to 27.070
Flywheel end 0.9860 to 0.9870 25.045 to 25.070
Camshaft journals fit clearance 0.0012 to 0.0028 0. 030 to 0.070
Cam lift (C, L and CL) 0.3425 8.700
Cam lift (Sport):
Inlet 0.3622 9.200
Exhaust 0.3642 9.250
Standard tappet bore diameter 1.4567 to 1.4577 37.0 00 to 37.025
Standard tappet outside diameter 1.4557 to 1.4565 36.975 to 36.995
Tappet fit clearance 0.0002 to 0.0020 0.005 to 0.05 0
Shim thickness 0.1279; 0.1299; then
0.0039 steps to 0.1850

3.2b; 3.30; then
0.10 steps to 4.70

Auxiliary shaft inches mm
Diameter of bush bores in crankcase:
Front 1.6339 to 1.6350 41.500 to 41.530
Rear 1.5733 to 1.5745 39.962 to 39.992
Fitted bush internal diameter:
Front 1.5143 to 1.5151 38.464 to 38.484
Rear 1.4553 to 1.4561 36.964 to 36.984
Diameter of shaft journals:
Front 1.5115 to 1.5125 38.393 to 38.418
Rear 1.4525 to 1.4535 36.893 to 36.918
Bush fit There must always be an interference fit
Shaft/bush fit clearance (front and rear) 0.0018 to 0.0036 0.046 to 0.091
Lubrication system
Oil pump Four lobe rotor type
Pump drive Through auxiliary shaft
Oil pressure relief valve Incorporated in pu mp
Pump rotors endfloat 0.0018 to 0.0047 0.045 to 0.120
Outer rotor to body clearance 0.0006 to 0.002 2 0.016 to 0.055
Inner to outer rotor clearance 0.0010 to 0.00 39 0.025 to 0.100
Oil pressure at 212°F (100°C) 50 to 70 Ibf/in
2 (3.5 to 5 kgf/cm2)

Cooling system
Radiator fan thermal switch
Cuts in . 194° to 201°F (90° to 94°C)
Cuts out 185° to 192°F (85° to 89°C)
Engine coolant thermostat
Starts to open 176° to 183°F (80° to 84°C)
Fully open 205°F (96°C)
Impellor vanes to pump body fit clearance 0.0315 to 0.0512 in (0.8 to 1.3 mm)

Radiator cap relief pressure 11.4 Ibf/in
2 (0.8 kgf/cm2)

Fuel system
Weber 32 ICEV 16/150 carburettor (C, L and CL model s)
Venturi diameter 0.8465 in (21.5 mm)
Main jet . 0.0453 in (1.15 mm)

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
10/34
Lamps
Headlamps (C, L and CL)
Headlamps (Sport)
Brake and rear light
Turn indicators
Reversing lights
Parking lights
Number plate
Courtesy light
Boot light
Turn repeaters
Cigar lighter light
Instrument panel
Ignition warning
Turn indicator warning
Headlamp warning
Coolant temperature warning (L models)
Oil pressure warning
Fuel warning
Hazard warning
Sidelamp (out) warning (Sport only)
Brake warning (Sport only)
Heated rear window warning (Sport only)
40/45 watts
55/60 watts (Halogen)
5/21 watts
21 watts
21 watts
5 watts
5 watts
5 watts
5 watts
4 watts
4 watts
3 watts
3 watts
1.2 watts
1.2 watts
1.2 watts
1.2 watts
1.2 watts
1.2 watts
3 watts
1.2 watts
1.2 watts

Fuses
For fuse details (127 Special, L, C, CL and Sport) see Sections 23 or 24

Steering and suspension (Sport only)
Steering angles
Inner wheel 34° 50’
Outer wheel 32° 10’
Front wheel alignment (toe setting)
Laden 0.079 in (2.0 mm) toe-in to 0.079 in (2.0 mm) toe-o ut
Unladen 0.138 in (3.5 mm) to 0.217 in (5.5 mm) toe-in

Roadwheels
Size 4½ B x 13
Tyres 135 SR-13 or 155/70 SR-13

All 1049 cc models Ibf ft kgf m
Main bearing cap bolts 59 8.2
Engine mounting securing bolts 43 6
Cylinder head to block bolts and nuts:
1 st stage 30 4.1
2nd stage 45 6.2
Final stage 61 8.5
Manifold to head nuts 20 2.8
Connecting rod big-end nuts 38 5.2
Flywheel to crankshaft bolts 61 8.5
Driven gear (Plastic) to camshaft retaining bolt 87 12
Driven gear (steel) to camshaft retaining bolt 87 1 2
Camshaft cap nuts 14 2

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
11/34
Ignition distributor clamp nut 11 1.5
Oil pump to crankcase bolts 13 1.8
Cylinder head outlet pipe bolt 16 2.2
Water pump/alternator drive pulley nut 101 14
Alternator bracket to crankcase bolt 20 2.8
Alternator to lower bracket bolt 36 5
Cylinder head upper bracket bolt 20 2.8
Alternator to upper bracket nut 36 5
Upper bracket securing bolt 13 1.8
Oil pressure switch 24 3.3
Coolant temperature switch 36 5
Spark plug 27 3.8

Sport models only
Engine
Flexible mounting to body (engine side) 65 9.0
Flexible mounting support (engine side to body)
18 2.5
Flexible mounting upper support to gearbox 18 2.5
Engine crossmember to body 18 2.5
Flexible mounting support nut (gearbox side) 18 2.5
Flexible mounting support bolt to body
(gearbox LH side) 65 9.0
Steering and suspension
Steering wheel retaining nut 22 3.0
Front wheel bearing ring nut 44 6.0
Front wheel hub nut 160 22.0
Roadwheel bolts 64 8.8
Front suspension track control arm to body 20 2.7
Front suspension balljoint to hub carrier 40 5.5
Rear wheel hub nut 160 22
Transmission
Starter motor bolt to bellhousing lower support 18 2.5
Gear selector shaft nut 18 2.5
Upper gear lever relay lever 22 3.0
Idler support securing nut 18 2.5
Differential case flange to gearbox housing 18 2.5

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
31/34


Fig. 13.4 Engine mounting (right-hand side) (Sec.3) Fig. 13.5. Engine mounting (left-hand side) (Sec.3)

1 – Mounting
2 – Crankcase
1 – Mounting to chassis bolts
2 – Mounting
3 – Mounting to transmission bracket

both the inlet and exhaust manifolds which are
on the same side of the engine.
Engine removal - 127 Special and 127
from chassis number 1104290 onwards
94 The removal of the engine assembly from
these models is slightly different from that
described in Chapter 1, owing to redesigned
engine mountings.
95 For the later type of mountings,
disconnection of the engine is achieved by
removal of the engine suspension mounting
securing bolts after taking the weight of the
assembly on a hoist.
96 On refitting the assembly tighten the securing
bolts to the specified torque load.
4. Fuel system

Carburettors - general
1 On L, C and CL models the 1049 cc engine is
fitted with either a Weber 32 ICEV 161150 or a
Solex C32 TDI/4 carburettor with a downdraught
single venturi and automatic coolant heated
choke (photos).
2 On Sport versions, a dual venturi Weber
carburettor is fitted with manual choke.

Weber or Solex single venturi
carburettors


Removal and refitting
3 Remove the air cleaner
4 Disconnect the throttle cable (photo).
5 Disconnect the distributor vacuum pipe
(photo). 6 Disconnect the fuel flow and return
hoses 7 Disconnect the coolant hoses from the
automatic choke housing and tie the pipes as
high as possible to prevent coolant loss (photo).
8 Unbolt the carburettor flange mounting bolts
and lift the carburettor from the manifold.
9 Refitting is a reversal of removal, but use a
new flange mounting gasket
Dismantling and adjustment
10 Clean the outside of the carburettor, remove
the top cover screws and lift off the cover.
11 Clean out the float bowl.
12 Any jets or bleed screws if removed, should
only be cleaned by blowing air through them.
Never probe with wire or their calibration will be
ruined.
13 Check the float level by holding the
carburettor cover vertically so that the float
hangs down, and then measure between the
casting flange and the nearest point of the float.
Adjust if necessary by bending the float arm tab
until the clearance conforms with the
Specifications according to carburettor.
14 The automatic choke will not normally require
dismantling, but if the cover is removed, make
sure that the centre index marks on the cover
and housing are in alignment before tightening
the choke cover screws.
15 On later carburettors, the mixture screw is
fitted with a tamperproof cap and adjustment to
the slow-running should therefore be limited to

Fiat 127 Internet Fan Club (http://fiat127.okruhy.cz) Fiat 127 - 1050
32/34

altering the throttle speed screw.
16 On earlier carburettors, or if new components
have been fitted to carburettors having a
tamperproof screw, then the slow-running and
mixture can be altered, but only if an exhaust
gas analyser is available in the case of later
carburettors, after the tamperproof cap has been
broken off.
17 On earlier units, use a device such as a
mixture adjustment aid or a vacuum gauge fitted
in accordance with the manufacturers'
instructions to obtain the correct slow-running
adjustment.
18 On later units, an exhaust gas analyser,
again used in accordance with the maker's
instructions, will ensure that the CO level is
within the limits specified. Fit a new tamperproof
cap on completion.
Weber dual venturi carburettor

Removal and refitting
19 These operations are similar to the
operations described in paragraphs 3 to 9 of this
Section, but the unit is of manually operated
choke design and will therefore not have coolant
hose attachments. A choke cable is fitted
instead.
Dismantling and adjustment
20 The operations are similar to those described
for the single venturi type carburettor, once the
upper body has been removed (six screws).
21 If jets are extracted, identify them as to which
side of the carburettor (primary or secondary)
they came from.


4.4 Throttle cable connection to Weber single ventu ri
carburettor 4.5 Weber single venturi carburettor installed (va
cuum pipe
arrowed


4.7 Weber single venturi carburettor showing coolan t hoses
(arrowed) to automatic choke housing. Note fuel hos es
connected to top right of carburettor 7.6 Location of fuse block - 1049 cc engine models